跳至主要内容

The Characteristics of Finger Wear Tester

Product features tend to change over time, the visual appearance is often the consumer to judge the quality of life during the product quality is good or bad. Thus, durability and wear resistance during normal use affect the overall impression of product quality. Damaged surfaces are some of the main causes of poor quality. So in the production of wear testing required, and then an effective evaluation of the product can effectively meet the requirements of consumers, to consumers the feeling of high-quality products.
Finger wear test At present, many instruments exist, such as the electronic button wear test, the current use of more RCA tape wear instrument, the same universal finger wear tester can also be used to measure the electronic button wear test. Below to interpret the universal finger wear tester:Universal finger wear tester:The finger on the surface slides to produce the highest biomechanical feedback when the object interacts with the object. When touching the surface, the fingers are mechanically struck, followed by push-slip motion. In addition to mechanical wear, sweat, body oil, and / or customers are more concerned with the product because the skin may react chemically with the surface of the product and promote further degradation. This combination of mechanical and chemical forces can be tested with TRIBOTOUCH.
Universal finger wear tester is designed to test laboratory samples or finished products under actual conditions of life. The combination of mechanical and chemical stresses produced by finger wear passes the international standard. The TRIBOTOUCH defaults to the biomechanical systems used to accurately reproduce complex fingers from these specifications, and the machine can change the applied pressure or chemical parameters for a product in different situations. This flexibility design allows an instrument to fit into multiple user-defined conditions.
The movement of the piston (artificial finger) is electronically controlled to simulate the wear of the product. Unlike other systems that rarely use pneumatic cylinders, they can wear out over time and give different results. TRIBOTOUCH uses a linear motor every time to ensure accurate application of pressure within the machine's life. The components used to make TRIBOTOUCH are high quality and will ensure high reliability and low maintenance in the next few years.

评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...