Structure of xenon lamp aging tester
1. Test box
The test case is made of corrosion-resistant material, and its internal device includes the radiation source and sample frame of the filter system.
2. Radiation source and filtration system.
Radiation source is composed of one or more of the xenon lamp, they produce a radiation filter filtered light system, make the irradiance in the sample frame with the relative spectral power distribution of plane of the sun's ultraviolet and visible radiation approximate or with 3 mm glass filtration of solar ultraviolet and visible radiation approximation.
3. Test box body adjustment system.
In order to maintain the black mark or blackboard temperature of the test case, the dust air should be circulated in the box, and its temperature and humidity are controlled. The temperature and relative humidity of the air in the test box are controlled by the temperature and humidity sensor, and the sensor is not directly exposed to radiation. The regulation of relative humidity must be distilled water or softened water.
4. The device for wetting the sample.
The test samples used throughout the wetting process should be wetted in one of two ways:
A) spray on the surface;
B) the sample is immersed in water in the test case.
If the sample is rotated around the radiant source, the nozzle of the water jet should be able to arrange each sample as required.
The conductivity of distilled water or softened water used for wetting should be less than 2 mu S/cm and the distillation residue is less than 1mg/kg.
5. Sample frame
The sample frame shall be made of inert material.
6. Black standard/blackboard thermometer.
In dry segments, use a black standard thermometer or chalkboard thermometer to measure the temperature of the sample surface.
7. Radiation meter.
The irradiance E and exposure radiant energy H on the surface of the test box should be measured by the radiation meter of the photoelectric receiver with a spherical field and a good cosine curve. The radiation meter shall be calibrated according to the spectral distribution listed in schedule B1, and the calibration value shall be checked according to the manufacturer's own manual.
1. Test box
The test case is made of corrosion-resistant material, and its internal device includes the radiation source and sample frame of the filter system.
2. Radiation source and filtration system.
Radiation source is composed of one or more of the xenon lamp, they produce a radiation filter filtered light system, make the irradiance in the sample frame with the relative spectral power distribution of plane of the sun's ultraviolet and visible radiation approximate or with 3 mm glass filtration of solar ultraviolet and visible radiation approximation.
3. Test box body adjustment system.
In order to maintain the black mark or blackboard temperature of the test case, the dust air should be circulated in the box, and its temperature and humidity are controlled. The temperature and relative humidity of the air in the test box are controlled by the temperature and humidity sensor, and the sensor is not directly exposed to radiation. The regulation of relative humidity must be distilled water or softened water.
4. The device for wetting the sample.
The test samples used throughout the wetting process should be wetted in one of two ways:
A) spray on the surface;
B) the sample is immersed in water in the test case.
If the sample is rotated around the radiant source, the nozzle of the water jet should be able to arrange each sample as required.
The conductivity of distilled water or softened water used for wetting should be less than 2 mu S/cm and the distillation residue is less than 1mg/kg.
5. Sample frame
The sample frame shall be made of inert material.
6. Black standard/blackboard thermometer.
In dry segments, use a black standard thermometer or chalkboard thermometer to measure the temperature of the sample surface.
7. Radiation meter.
The irradiance E and exposure radiant energy H on the surface of the test box should be measured by the radiation meter of the photoelectric receiver with a spherical field and a good cosine curve. The radiation meter shall be calibrated according to the spectral distribution listed in schedule B1, and the calibration value shall be checked according to the manufacturer's own manual.
Learned a lot, thank you! Are you interested in a relative machine named Light & Weather Fastness Tester? Welcome to communicate with us!
回复删除此评论已被博客管理员删除。
回复删除