跳至主要内容

Skills for prevent Dry cleaning problems


Dry cleaning Test Machine is suitable for the determination of the change of physical indexes such as the appearance color,size change and peel strength of the clothing and various textiles by organic solvent  , alkaline solution after dry cleaning.



Dry cleaning of the dry washer and maintenance of the dry-cleaning machine should be carried out after the dry-cleaning machine is cooled to prevent burns caused by incorrect opening. Steam inlet pipe should be equipped with decompression device to prevent overpressure steam into the dry cleaning machine and cause the risk of pipe burst. Often check the steam pipe with or without aging, leakage phenomenon, to prevent the collapse of broken pipe fittings.






Fire hazard:
A, according to the safety requirements of electricity matters, often looking for electricity hidden dangers, to prevent electrical ignition caused by fire.
B, some additives such as gasoline, benzene and other flammable materials should be stored separately in a safe, cool and ventilated place, to prevent the evaporation of flammable substances caused by fire.
C, heat-conducting oil heating dry cleaning machine should pay attention to the use of special high flash point heat transfer oil, and thermal oil should be replaced once a year to prevent the heat transfer oil and carbonized and flammable. Often check the heating element terminal is solid, whether the aging of the wire, the best regular replacement to eliminate short-circuit ignition hazard. The oil spill of the distillation tank should prevent water from entering and avoid the burning of the heat transfer oil due to the entry of water.
D, heat conduction oil heating in the drying heater there is a lot of heat transfer oil, if the heater leakage will cause heat oil overflow, into the duct and the cage, damage to clothing and even lead to fire, explosion.
E, a lot and more expensive clothes do not close to the dry cleaning machine suspension, or in the event of a fire accident will cause significant economic losses.
F, do not dip a lot of flammable solvent clothing in a dry cleaning machine drying.

-------------------------------------------------------------------
For more information about our testing instrument, please contact
·website:http://www.qinsun-lab.com/
· +86-21-6780 0179
· info@qinsun-lab.com
· or leave your comments below

评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...