跳至主要内容

How To Measure Color Fastness To Perspiration With A Perspiration Tester ?


Perspiration color fastness tester is widely used in testing textile anti-sweat, sea water, saliva, distilled water and other color fastness. Perspiration Tester Scope of application: all kinds of textile materials, textiles, perspiration and color fastness test and determination of various colored, colored textiles sweat, sea water, saliva, distilled water and other color fastness performance.

Perspiration color fastness meter operation method:
1, as a printing and testing equipment, it is prepared according to the standard sweat, PH solution solution, PH range should be 4.3 ± 0.2, from the sample material cut 6x6cm test pieces, and cut the same size of multi-fiber cloth, The weight of the sample and the multi-fiber cloth.

2, place each test piece and a multi-fiber cloth in the diameter of 9cm, 2cm deep disc, in the dish plus anti-sweat soaking test pieces and multi-fiber cloth for 30 minutes. The test piece was repeatedly rolled and weighed until it was 2.25 ± 0.05 times the weight under dry conditions.

3, the test pieces and multi-fiber cloth, Shuo material board placed on the anti-perspiration, to keep the total number of panels for the 21-layer, put the last layer, put the pressure plate, and add weight total weight 10.0lbs.

4, lock the screws, and put in the oven, set the oven to keep the temperature 38 ± 1 ° C for 6 hours, remove the tester, separate each test piece and multi-fiber cloth.


As a printing and dyeing test equipment, perspiration color fastness tester test principle is the combination of samples by artificial sweat soaking, after color fastness perspiration tester after pressure treatment, dry, assess the color of the sample and stick to the fabric Color and color fastness were measured using the Datacolor colorimeter.

-------------------------------------------------------------------
For more information about our testing instrument, please contact
·website:http://www.qinsun-lab.com/
· +86-21-6780 0179
· info@qinsun-lab.com

· or leave your comments below

评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...