跳至主要内容

Study on Footwear Bending Tester


      Footwear is clamped to the machine at the toe end by using the appropriate toe clamp from one of five pairs supplied. The heel end is secured to the flexing bar. A predetermining counter is fitted and once the appropriate number of flexes has been registered, the machine will stop so that the shoe can be inspected.The moving parts of the machine are covered by a hinged guard which is fitted with the latest safety device to prevent access while the machine is still in use. 

 The machine is robust and non-corrosive materials are used in the relative components required..A similar machine is available for testing high leg boots where water depth can be increased to cover the whole forepart of the footwear, highest to the metal ring area.Details available on request.
   The Footwear Bending Tester is supplied in both single or twin station models and the operation simulates the flexing of footwear during wear. The angle of flex is adjustable up to 50°. The machine may be used to predict the adhesive failure and cracking of footwear in wear. It is particularly useful in assessing problems associated with the sole structure.

Footwear Flection Tester Structure:The machine is composed of:
a) Plate forced to oscillate with a frequence of 140 times of oscillation/minute.
b) Two adjustable artificial feet either in size and position.
c) Digital cycle counter, with a reset function, to set the desired number of cycles for the test.
d) An angle regulation with adjustable zero start point.
e) A water container with a samll pump, connected to the workstation which allows to keep wetting the sole of the loaded sample shoes. (for wet tests please use the cover)
f) Control panel can perform the switching of instrument working state and the setting of counter, including: a general magnetothermic switch, a Start button, a Stop button, a Manual button, a Reset button, a programming cycle counter.
For more information about our testing instrument, please contact

 ·website:http://www.qinsun-lab.com/

 · Phone :+86-21-6780 0179
· E-mail :info@qinsun-lab.com 

评论

发表评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...
发表评论
阅读全文

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...
发表评论
阅读全文

Automotive materials and components testing

Automotive Original Equipment Manufacturers (OEMs) demand the highest quality components throughout the supply chain. Every automotive material and component must undergo rigorous testing and meet the highest industry and legal requirements. Qinsun-Lab assists manufacturers and suppliers with independent assured testing services against a wide range of OEM testing specifications, national (BS, ASTM, DIN, JASO) and international (ISO, EN, SAE) standards. SATRA’s testing services are accredited to ISO 17025. Flammability Motor vehicles contain components that burn if subjected to a large enough ignition source. These include seat upholstery, headlining, trim panels and floor coverings. Qinsun-lab can conduct a range of flammability tests including FMVSS 302 and ISO 3795. Abrasion and Scratch Tester Automotive materials experience mild abrasive actions from users entering the vehicle and being seated while driving or travelling. Qinsun-lab has a range of tests including Mar...
3 条评论
阅读全文