跳至主要内容

4 Secrets About Artificial Synthetic blood penetration tester Setup

 4 Secrets About Artificial Synthetic blood penetration tester Setup That Nobody Will Tell You:

1. Place the test tank horizontally on the test bench, and put the normal outer surface of the protective clothing material fiber into the test tank. The test tank will be used to fill synthetic blood. A support mesh is used on the normal inner surface of the sample to support the malleable or elastic material.




2. Assemble the components of the test tank:

Install gaskets between the penetration test slot and the test sample, between the test sample and the support mesh, and between the support mesh and the flange cover. Cover the flange cover and the transparent cover to close the test slot. It is recommended to use a polytetrafluoroethylene (PTFE) thermal coil between the penetration test cell and the test sample to prevent liquid leakage. NOTE: A clear plastic film can also be used as an alternative to the clear lid.

3. Tighten each screw that penetrates the test slot to a torque of 13.6N·m.

4. Load the penetration test tank into the test device in a vertical direction (with the discharge valve downward), as shown in Figure ⒉, but the test tank is not connected to the air pipeline.


The artificial Synthetic blood penetration tester's single-chip microcomputer automatically controls the test program, automatically timing, and alarms when the test is over; the pneumatic valve will simulate splashing blood or other body fluids to dispense on the sample cover. Welcome to order!

评论

发表评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...
发表评论
阅读全文

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...
发表评论
阅读全文

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...
1 条评论
阅读全文