跳至主要内容

UV Accelerated Weathering Tester accuracy will be affected by what factors?

UV Accelerated Weathering Tester test accuracy is affected by many external factors, such as the temperature inside the box, cyclone rate, environmental humidity, etc., so we usually in the test must pay attention to grasp these conditions.


Influencing factor one: dust and other surface air pollutants will be more serious, changing the digestive absorption characteristics of the illuminated surface layer of the object block. Unless otherwise required, the experiment should ensure that the test product cleanup, but in the identification of the efficacy of surface air pollutants, the relevant standards should require the test product metal surface treatment and other necessary content.



Influencing factor two: short-wave ultraviolet radiation source under the ozone caused by the general can be based on the effect of positive spectrometer kinetic energy all over the radiation source filter out of the environmental test chamber, because the ozone and other environmental pollution vapor will affect, some raw materials deterioration of the whole process, unless the relevant standards require otherwise, be sure to discharge this harmful substances out of the box on.


Influencing factor three: a variety of support frame thermal characteristics and installation methods, UV Accelerated Weathering Tester will have a serious impact on the temperature composition of the experimental specimen, for should also be sufficient to take into account, so that its heat transfer characteristics can mean the typical specific application conditions. Most of the test specimens are installed in the actual requirements of the thermal characteristics of a variety of rising support frame or pad bracket, the pad bracket and the installation method and placement of test specimens and other detailed provisions should be related to the requirements of the standard.



Influencing factor four: under different environmental humidity standards, the photochemical deterioration utility of various raw materials, architectural coatings, and plastics and other chemical substances are vastly different, and their provisions on environmental humidity standards are the same as each other, so the actual environmental humidity standards are explicitly stipulated by the relevant standards.


Influencing factor five: direct light link or stop light link, the temperature in the box should be required by the experimental procedure flow (A, B or C) to control, the relevant standards should be in accordance with the machine and equipment, or components of the reservation of the main use requirements in the direct light link need to exceed the temperature


Influencing factor six: near the surface of the test product cyclone rate size in addition to the impact of the test product to raise the temperature, and even also make the monitor radiation intensity of the open temperature difference power stack a significant deviation.

Tag:

uv accelerated weathering tester,ultraviolet light accelerated weathering tester,accelerated weathering tester,uv light accelerated weathering chamber,bench ultraviolet light accelerated weathering tester,accelerated weathering,uv weathering tester,weathering,accelerated weathering uv chamber,accelerated aging tester,weathering tester,enviromental test chamer uv accelerated weathering tester,uv light accelerated,uv light accelerated machine manufacturer

ps: (WLJCDM809)




评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...