跳至主要内容

Safe Design Of Melt Flow Tester

Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR).Melt Flow Testers has been designed to determine the melt flow index property of thermoplastics. Any other attempt to use this instrument in any fashion other than its intended use may expose the instrument or the operator to dangerous.

Sturdy design includes housing for temperature and steel test cylinder, which is heated by a precision dual zone, insulated and jacked in a columniform housing. A tool rack is provided for convenient access to frequently used operating tools.

The Basic Unit Of Melt Flow indexer consists of Temperature Measure Element, Temperature Control System, Automatic Cut-off System, Automatic Timing system, the Control Panel, the Pull Handle and the Tool Rack.

Temperature Measure Element:A platinum RTD probe senses the cylinder temperature, sending the temperature signals to the temperature controller, which regulates the temperature of the upper and lower portions of the cylinder to within 0.1℃. The test point of temperature is 1cm high over the Die and the temperature of the cylinder is displayed as the Actual Temperature.

Temperature Control System:The scope of the temperature is controlled from 120℃to 450℃, the accuracy is ±0.5℃, the Temperature fluctuation is ±0.5℃.

Cut-off System:This unit is designed below the furnace and cut off specimens according to preset parameters. The unit of timer is one second.
For more information about our testing instrument, please contact

·website:http://www.qinsun-lab.com/

· Phone :+86-21-6780 0179

· E-mail :info@qinsun-lab.com

评论

发表评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...
发表评论
阅读全文

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...
发表评论
阅读全文

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...
1 条评论
阅读全文