跳至主要内容

Blanket Flammability Tester Method

     Specimens cut from the blanket fabric are prepared by brushing if they have a raised fiber surface and by drying. The dried specimen is held in a special apparatus, a standardized flame is applied to the surface for a specified time under controlled conditions, and burning, charring, or discoloration of a paper monitor is noted. Two classes of flammability are described.


     This test method of Blanket Flammability Tester should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.A burn of sufficient intensity to discolor a paper monitor in specified contact with the surface of the test specimen indicates ignition of the blanket surface.

    Blanket Flammability Tester is designed to determine the ignition resistance property of blanket fabrics and surface flame spread performance of fabric. A standardized flame is applied to the surface of specimen for a special time under controlled conditions, and burning, changing, or discoloration of a paper monitor is noted to classify flammability of tested fabric.
-------------------------------------------------------------------
For more information about our testing instrument, please contact
·website:http://www.qinsun-lab.com/
· +86-21-6780 0179
· info@qinsun-lab.com

· or leave your comments below

评论

此博客中的热门博文

Multi-Functional Scratch tester For automotive interior materials

          Multi-Functional Scratch tester is applicable to all types of wiping performance test of automotive interior materials; test equipment integrated three domestic standards (fingers scraping method, a hundred grid method, and plastic scraping finger scraping method).         Scratch tester is an electronic instrument capable of measuring critical load, adhesion, scratch resistance and bond strength for a wide range of surfaces. Scratch tester measures the scratch resistance of a sliding and moving surface in the relative motion to a stylus. The stylus is forced/pressed against the moving surface with precise controlled force which is normal to the surface and tangential force at the contact has to be measured.         Scratch tester can be utilized for all type of industrial coating from the plasma layers used in semiconductor and optical technology used in decorative coatings used for automotive and consum...

Reveal the standards for textile breathability testing and let you understand it in seconds!

 Reveal the standards for textile breathability testing and let you understand it in seconds! Breathability testing is a measure of how much gas can pass through a textile. However, there is no single "optimal" air permeability value, as it depends on the specific circumstances in which the textile is used. For example, if it is used to make sportswear, it is hoped that it has good breathability; if it is used to make insulating clothes or warm clothes, it is hoped that it can block the cold well. Therefore, when testing the air permeability of textiles, the purpose of using the textile must be clearly understood in order to obtain reasonable values. In order to accurately and quickly test the true breathability performance of a sample, specially designed and developed instruments must be used. Testing methods generally include: fabric thickness (Thickness), fabric density (Density), fabric water absorption rate (Water Absorption Rate), evaporation and mass transfer (Moistur...

Test Methods of Universal Pilling Assessment Viewer (PAV)

Universal Pilling Assessment Viewer enables fabric to be assessed while still mounted on a Martindale head. The Pilling Assessment Viewer (PAV) for the textile market has been developed with the help of a major textile company in accordance to BN EN ISO 12945 standards incorporating all 3 parts and adopting the following test methods: Part 1: ICI Pilling box method (BS 5811) Part 2: Modified Martindale method (SN 198 525) Part 3: Atlas random tumble method (ASTM D 3512-96) It uses D65 Artificial Daylight (with CWF optionally available), as specified by many retailers. Other test methods can also be viewed, including those specified by major retailers. Other results of test methods that can be viewed include: BS 5811:1986 Determination of resistance to pilling and change of appearance of fabrics. ICI modified pill box for snagging Fleece appearance and surface change after washing Other test methods as specified by several major retail outlet. To optimize c...